- 394 - frf501g thru frf507g isolation 5.0 amps. glass passivated fast recovery rectifiers voltage range 50 to 1000 volts current 5.0 amperes features low forward voltage drop high current capability high reliability high surge current capability mechanical data cases: ito-220ab molded plastic epoxy: ul 94v-0 rate flame retardant terminals: leads solderable per mil-std-202, method 208 guaranteed polarity: as marked high temperature soldering guaranteed: 260 /10 seconds 0.25?,(6.35mm) from case. mounting position: any weight: 2.24 grams mounting torque: 5 in ? 1bs. max. ito-220ab dimensions in inches and (millimeters) maximum ratings and electrical characteristics rating at 25 ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol frf 501g frf 502g frf 503g frf 504g frf 505g frf 506g frf 507g units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current i (av) 5.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 30 a maximum instantaneous forward voltage @2.5a v f 1.5 v maximum dc reverse current @ t c =25 at rated dc blocking voltage @ t c =125 i r 5.0 100 ua ua maximum reverse recovery time ( note 1) trr 150 250 500 ns typical junction capacitance ( note 2 ) cj 140 pf typical thermal resistance ( note 3 ) r ja 4.0 o c/w operating temperature range t j -65 to +150 storage temperature range t stg -65 to +150 notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied reverse voltage of 4.0 volts d.c. 3. mount on heatsink size 2" x 3" x 0.25" al-plate .272(6.9) .248(6.3) .543(13.8) .512(13.2) .110(2.8) .098(2.5) .606(15.5) .583(14.8) .112(2.85) .100(2.55) .134(3.4)dia .113(3.0)dia
- 395 - fig.1- reverse recovery time characteristic and test circuit diagram 50 noninductive non inductive oscilloscope (note 1) pulse generator (note 2) dut (+) 50vdc (approx) (-) notes: 1. rise time=7ns max. input impedance= 1 megohm 22pf 2. rise time=10ns max. sourse impedance= 50 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm ratings and characteristic curves (frf501g thru frf507g) fig.2- maximum forward current derating curve average for ward current . (a) 0 50 100 150 0 1.0 2.0 3.0 case temperature. ( c) o fig.3- maximum non-repetitive forward surge current per leg peak for ward surge current . (a) 1 2 5 10 20 100 50 5 15 10 number of cycles at 60hz 8.3ms single half sine wave jedec method fig.6- typical instantaneous forward characteristics per leg instantaneous for ward current . (a) 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 instantaneous forward voltage. (v) tj=25 c pulse width=300 s 1% duty cycle o fig.2- typical reverse characteristics per leg instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 0.1 1.0 10 100 1000 percent of rated peak reverse voltage. (%) tj=25 c 0 tj=125 c 0 fig.4- typical junction capacitance per leg capacitance.(pf) 0.1 0.5 1.0 5 10 50 100 500 1000 50 100 150 200 250 300 reverse voltage. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 5.0 4.0 30 25 20 0.04 0.01 0.02 0.1 0.2 0.4 1.0 2.0 4.0 8.0
|
